menu

Search 4,514 docs, articles & videos from the world’s leading Automotive part manufacturers

  

4511 results

...Control arm bearings Caution: Collar bearings were installed until August 1999. The installation of such bearings is not suitable any longer and they have since been replaced with slot bearings. Suitable for rear axles of the following series: BMWE36,E46,X3 febi no. 14923 reference n...

...Modified strut bearing with centring pin. Suitable for the BMW series: BMW E 36, Z 3 and Z 4 febi no. 24316 Comparison number 31 33 6,769,585 (31336769585) As well as a new internal design and material, the modified febi strut bearing now also boasts a centring pin. This allows the b...

...The outer diameter has changed on front wheel hubs suitable for all Opel Astra G / Zafira A models with five hole rims and ABS. Opel Astra G / Zafira A front wheel hubs Version with new cap febi no. 24164 comp. no. 1603 211 S1 (1603211S1) Version without cap febi no. 14623 comp. no....

...febi offers a new stabilizer mounting for Audi, Seat and VW in a new design which now has replaced the old design. Please note that when replacing the stabilizer mounting, the clamp should also be replaced. Stabilizer mountings for Audi, Seat and VW febi no. 22804 OE no. 1J0 411 314 R...

...Complete suspension arm fitting BMW E 46: 316i - 330d (excl. 4x4) 02.98 - 02.07 BMW Z4  Suspension arm rubber mountings must not be re-used, as the bushed get damaged during removal. We now include in our kits the bolts which must be tightened to 59nM. This means reduced fitting time...

...Best-value repair solutions Whenever the bush or the ball joint of the suspension arm failed in the past, the complete component had to be replaced, because it was only available as a unit. febi now has a better solution: Each suspension arm component is now available as an individual p...

...A complete solution for Ford Mondeo 1+2! Due to a change of design of the anti roll bar mounting by the car manufacturer, problems occurred when fitting the stabilizer mounting (febi 27355). The former semi-circular design has now been changed to a flat design identical to the original...

...Complete solution for a Renault timing belt change! i.e. febi no. 19951 febi no. 23206 KLANN tool For the engines 1.4 16V (K4J) 1.6 16V (K4M) 1.8 16V (F4P) 2.0 16V (F4R) 2.0 16V (F4R) Ref. no. 77 01 477 014 (7701477014)  Ref. no. 77 01 477 014 (7701477014)  Ref. no. 77 01 476 674 (...

...Just two parts for nearly the whole vehicle parc! Now available in the febi range: Universal CV boot repair kits for cars and universal CV boot repair kits for LCVs and SUVs! CV boot kit for cars febi no. 27730 with clamps and 90g of grease febi no. 02582 CV boot kit for LCVs / SUVs feb...

...Green, mineral hydraulic fluid for Citroën hydraulic pneumatic chassis (type II)! febi number 24704 LHM (24704LHM) (1 litre)  Reference number 9979.A1 (9979A1) With excellent low-temperature properties, this mineral based hydraulic fluid specifically fits the hydraulic pneuma...



...[Previous 10 pages] ... 117 | 118 | 119 | 120 | 121 | 122 | 123 | 124 | 125 | 126 ...[Next 10 of 452 pages] ...
footerlogo
popup