4511 results

• 
• Type

  Technical Bulletin

• Clutch Replacement: Toyota Aygo, Citroen C1, Peugeot 107

• Jul 09

• Blue Print (202) Contact
• 

...INF119 Toyota Aygo-Citroen C1-Peugeot 107 Clutch Replacement Toyota Aygo / Citroen C1/ Peugeot 107 Clutch Application Specification Change of Clutch Diameter from 180mm to 190mm Vehicle Applications: Toyota Aygo - 1.0 (KGB10, 1KR-FE) Peugeot 107 - 1.0 (1KR-FE) Citroen C1 - 1.0 (1KR-F...

• 
• Type

  Installation Instructions

• Clutch Release Bearing Installation: Ford Escort/Fiesta/Orion/Mondeo

• Jan 13

• Autobiz (337)
• 

...Ford Escort / Fiesta / Orion / Mondeo (Non-Hydraulic Type) CLBT0005 Clutch RELEASE BEARING FITMENT INSTRUCTIONS Concerns The release bearing must be removed and replaced in accordance with the following instructions to ensure a correct fitment. Method Unscrew bolt to free fork pi...

• 
• Type

  Tech Tip

• Clutch Q & A

• Jun 11

• LuK (131) Contact
• 

...Clutch Q & A The modern-day vehicle uses a multitude of new technologies, not only in engine management systems, but also in transmission controls. LuK answers some questions about clutch replacement and some newer developments. LuK has been to the forefront in the development of new...

• 
• Type

  Technical Bulletin

• Clutch hydraulic circuit bleeding problem on Jeep/Chrysler

• May 23

• Blue Print (202) Contact
• 

...Blue Print Protips ADA103601, ADA103602, ADA103603, ADA103605, ADA103607, ADA103609, ADA103610 To fit: Jeep Cherokee, Grand Cherokee, Wrangler/Chrysler PT Cruiser, Neon, Voyager, Grand Voyager Clutch hydraulic circuit bleeding Problem Unable to purge the air from the clutch hy...

• 
• Type

  Technical Bulletin

• Clutch hydraulic circuit bleeding

• Jul 19

• Blue Print (202) Contact
• 

...PROTIPS Technical data can be subject to change | EN | JULY 19 PROTIPS Problem Unable to purge the air from the clutch hydraulic circuit. Therefore, resulting in no clutch operation.Cause The clutch hydraulic circuit is not equipped with a bleed nipple for purging the air, which maybe trap...

• 
• Type

  Technical Bulletin

• Clutch hub coatings - Lubricants are not always necessary

• Nov 15

• LuK (131) Contact
• 

...Fig. 1: Nickelled hubs must not be greasedFig. 2: Phosphated hubs must be greasedClutch hubs can have different types of coatings. For this reason, when working on the clutch the following points must be obser ved: • Nickelled hub splines (Fig. 1), characterised by their matte silver col...

• 
• Type

  Technical Bulletin

• Clutch grabs when shunting

• Dec 14

• LuK (131) Contact
• 

...Setting the clutch booster is only necessary if either the clutch pressure plate, clutch disc or piston rod has been replaced. A suitable diagnostic device is required for working on or adjusting the transmission control.Clutch grabs when shunting Manufacturer: Mercedes-BenzModels: Actr...

• 
• Type

  Technical Bulletin

• Clutch Fault Diagnosis Chart

• Jul 13

• Borg & Beck (26)
• 

...Borg & Beck DAMAGED DRIVEN PLATECAUSEDriven plate fitted wrong way round EFFECTClut\fh inoperative REMEDYRepla\fe driven plate asse\bbly and \fhe\fk \fover asse\bbly for da\bage. renew if ne\fessary DAMAGED SPLINE CAUSEFailure to \forre\ftly align spine with driven plate during gearbox...

• 
• Type

  Technical Bulletin

• Clutch disc with new first stage damper

• Dec 14

• LuK (131) Contact
• 

...Clutch disc with new first stage damper Six spring torsional damper with first stage damper for higher capacitySix spring damper with first stage damperIn addition to transmitting engine torque, the clutch disc has the task of preventing torsional engine vibrations from reaching the powe...

• 
• Type

  Technical Bulletin

• Clutch damage due to incorrect hub greasing

• Apr 24

• REPXPERT (32)
• 

...Clutch damage due to incorrect greasing of the hub To ensure that the clutch functions properly after replacement, the contact point between the clutch disc hub and the toothing of the gearbox input shaft must be greased. Not just any lubricant should be used here, but a special high-pe...