3957 results

• 
• Type

  Tech Tip

• LuK Clutch Academy - Skoda Rapid 1.6 TDi

• Sep 20

• LuK (132) Contact
• 

...See this and 1,000s more Tech Tips on TechTips.ie 48 August/September 2020 AUTOBIZ See this and 1,000s more Tech Tips on TechTips.ie Gearbox removal With the vehicle positioned on a vehicle lift – either a two-post or wheel-free is ideal – open the bonnet, disconnect the ai...

• 
• Type

  Technical Bulletin

• Peugeot 407 - Preventable Fuel Problem

• Sep 20

• Autobiz (359)
• 

...Automatic climate control means that the system can be set to a given temperature and forgotten. On this 2005 Mazda3, it was designed to be set at a comfortable temperature and then left to ensure the interior of the vehicle remained at the selected steady temperature. The system on this m...

• 
• Type

  Technical Bulletin

• Audi A4 - StrangeBrake Wear

• Sep 20

• Autobiz (359)
• 

...Automatic climate control means that the system can be set to a given temperature and forgotten. On this 2005 Mazda3, it was designed to be set at a comfortable temperature and then left to ensure the interior of the vehicle remained at the selected steady temperature. The system on this m...

• 
• Type

  Technical Bulletin

• MAZDA 3 - Heater Panel Problems

• Sep 20

• Autobiz (359)
• 

...Automatic climate control means that the system can be set to a given temperature and forgotten. On this 2005 Mazda3, it was designed to be set at a comfortable temperature and then left to ensure the interior of the vehicle remained at the selected steady temperature. The system on this m...

• 
• Type

  Technical Bulletin

• Kia/Hyundai Timing Belt Tensioner Installation

• Aug 20

• Blue Print (204) Contact
• 

...Kia Hyundai timing belt tensioner Problem This timing belt tensioner needs to be set correctly during the installation process. If this is not followed, this can cause the timing belt system to fail. Cause Removing the load pin too early influences the operation of the tensione...

• 
• Type

  Technical Bulletin

• Picoscope - Current clamp settings explained

• Aug 20

• PicoScope (102)
• 

...Current clamp settings explained Phil Rutt is explaining the current clamps settings for our current clamps. Oscilloscope...

• 
• Type

  Technical Bulletin

• Diesel injection pump drive on Ford 1.8 TDCi Lynx Engines

• Aug 20

• febi (172)
• 

...Diesel injection pump drive Various Ford models fitted with the 1.8 lynx diesel engine (up to year of construction 2008), the crankshaft drives the injection pump via a chain. During any replacement, it is advisable to replace all necessary parts included in the febi chain kit 46390....

• 
• Type

  Technical Bulletin

• Problems after Installing Intake Manifold Servo Motor

• Aug 20

• Pierburg (206)
• 

...INTAKE MANIFOLD SERVO MOTOR:PROBLEMS AFTER INSTALLATION Potential complaints:• Repeated malfunctions following installation of a new servo motor• Fluctuations in speed and jerking• Diagnostic trouble codes P1018, P208, P2011, P3135 DO NOT FORGET TEACHING-IN! Electric servo motors (01...

• 
• Type

  Technical Bulletin

• Ensuring correct A/C compressor oil filling quantities

• Aug 20

• MAHLE (151)
• 

...Technical Messenger Issue 03/2020 When replacing an air conditioning compressor, there are some important points you need to take into account to prevent direct failure of the new compressor and consequential damage to the air conditioning circuit. Flushing The system must be thoroughly f...

• 
• Type

  Technical Bulletin

• Finding the Cause of a Cabin Vibration

• Jul 20

• PicoScope (102)
• 

...Finding the cause of a cabin vibration with the PicoScope function generator Steve Smith is showing how he used the function generator in the NVH software to find the cause of a vibration in his car, which had been bothering him for a long time....