menu

Search 4,514 docs, articles & videos from the world’s leading Automotive part manufacturers

  

3584 PDF Files Listed

...Installing coolant pumps correctly Installation without additional sealantFig. 2: Coolant pump KIT with paper gasketOne of the most frequent causes of coolant pump failure is a damaged rotating mechanical seal.Before mounting a new coolant pump, use a scraper or a soft scouring pad to pr...

...Installation tip for timing belt kit CT 957 K1 – WP4: e.g. Audi / VW / Skoda / Seat 1.4 /1.6 16V Power Transmission Group Automotive Aftermarket ContiTech Power Transmission Group Philipsbornstrasse 1, D-30165 Hannover Tech. Hotline +49 (0)511 938 -5178 E-mail: frank.wissbroecker@ptg.co...

...Observe installation orientation Wheel bearing with passive encoderManufacturers: BMW, Mercedes-BenzModels: 3 (E36, E46, E90, E91, E92) 5 (E60, E61) 7 (E38) 8 (E31) X 3 (E83) X 5 (E53) Z3 (E36) Z8 (E52) E-Class (S124, W124)Part No.: 713 6492 80 713 6674 80 713 6...

  • img

  • Technical Bulletin

  • Installation of tensioner used in PowerGrip Kits

  • Jan 07

  • Gates (127) Contact
  • PDF

...Technical Bulletin 012 Copyright © 2006 Gates Corporation Page 1 of 6 # 012 31/03/2006 GATES REFERENCE : MAKE : MODEL : MOTOR : MOTOR CODE : K015543XS, K025543XS and K015559XS AUDI / SEAT / SKODA / VOLKSWAGEN A3, Cordoba, Ibiza, Inca, Leon, Toledo, Octavia, Bora, Cadd...

...faiauto.comInstallation informationPTFE Oil SealsImportant :• Ensure contact surfaces are clean, dry and damage free.• Carefully push seal into position, without damaging the PTFE material.• When fitted, do not start engine for a minimum of 4 hours.Važno:• Postarajte se da je kont...

...Preparation• Prehoning: grain size 150 (material removal of approx. 0.06 mm based on diameter)• Finish honing: grain size 280 (material removal 0.02 mm based on diameter)• Plateauhoning:grainsize400–600(removeprofilepeaks inafewstro...

...1Feeler gauge0.12PreparationInspectionFirst, clean the pistons thoroughly and remove all traces of oil carbon from the ring grooves. Remove the carbon from the oil return bores using a twist drill and tap wrench; clean the grooves without damaging the groove sides. Replace cracked, collaps...

...CABCAB1237954812346475121236Flange thicknessBearing widthFlange spacingDetails – flanged bearing halvesDetails – flat bearing shellsInstallationPress fit with protrusionMeasured across the par ting faces, the bearing shell is larger than the diameter of the bore. This produces good co...

...Mahle Technical Messenger Issue no. 04/2023 Installation notes for the oil filter insert OX 1141D There is a risk of inadequate lubrication if the O-rings are mounted incorrectly. The oil filter insert OX 1141D is supplied with all required sealing rings. However, if they are not mou...

...Installation notes for brake discs General note Please always observe the installation instructions or information leaflet that accompanies the product.  Brake discs may only be exchanged by persons with corresponding specialist knowledge.  Incorrectly-performed work could lead...



...[Previous 10 pages] ... 201 | 202 | 203 | 204 | 205 | 206 | 207 | 208 | 209 | 210...[Next 10 of 359 pages] ...
footerlogo
popup