Search 4,511 docs, articles & videos from the world’s leading Automotive part manufacturers
3584 PDF Files Listed
-
-
Technical Bulletin
- Universal clutch fitting instructions and General safety
-
Jan 17
- LuK (131) Contact
-
...SERVICE INFOTB1244Phone : +44 (0) 1432 264 264*Fax : +44 (0) 1432 375 760E-Mail : hfd-pm@schaeffler.comwww.schaeffler-aftermarket.co.uk* calls from the UK : 08457 001100· For accurate model i nformation plea se s ee LuK cat alogue· Die genaue Fahrzeugzuordnung entnehmen Sie bitte dem LuK...
-
-
Technical Bulletin
- Peugeot 807/Citroën C8 Timing Belt water ingress installation tip
-
Jan 17
- Contitech (157)
-
...Installation tip for timing belt kits CT1037K2 and CT1037WP1 for various Peugeot 807 and Citroën C8 2.2 HDI diesel engines Problem: Rainwater runs into the timing belt drive and causes corrosion and icing, resulting, in the worst-case scenario, in engine damage. Cause: The drainage...
-
-
Technical Bulletin
- Volvo XC90/S90/V90 - Condensation in vehicle interior
-
Jan 17
- Hella Ireland (1757)
-
...Volvo XC90/S90/V90 Model year: 2016 + 2017 Condensation in vehicle interior In the vehicles listed above, there is a chance of water getting into the interior. Over longer periods of time, this may also lead to malfunctions in the electrical systems. This may be caused by an incorrec...
-
-
Technical Bulletin
- Brake Fluid
-
Jan 17
- Hella Ireland (1757)
-
...Brake fluid Task Brake systems are complex entities in which many elements must work together perfectly to ensure safe functioning, even in extreme situations. The brake fluid plays a very important role in this, as it transfers the power from the pedals to the brake system by means...
-
-
Technical Bulletin
- Crankshaft Damper Pulley Mounting Bolts
-
Jan 17
- NTN-SNR (73)
-
...Some new damper pulleys require new bolts. Why replace the bolts? When a damper pulley is fitted and torqued correctly the retaining bolts are put under high stress loads, this stress causes the bolts to stretch and deform. If the old stretched or deformed bolts are re-...
-
-
Installation Instructions
- Mounting of shaft protection sleeves
-
Jan 17
- Pierburg (204)
-
...Repair shaft sliding surfaces quickly and simplyShaf t protection sleeves offer a cost-effective alternative to replacement or time-consuming remachining of the broken-in or worn shaf ts. The shaf t protection sleeve is slid easily over the worn sliding surface of the shaf t. This is of te...
-
-
Installation Instructions
- Installation of pistons - Step by step
-
Jan 17
- Pierburg (204)
-
...Preparation• Prehoning: grain size 150 (material removal of approx. 0.06 mm based on diameter)• Finish honing: grain size 280 (material removal 0.02 mm based on diameter)• Plateauhoning:grainsize400–600(removeprofilepeaks inafewstro...
-
-
Technical Bulletin
- Piston rings - Function and design
-
Jan 17
- Pierburg (204)
-
...Piston ringsFunction and designMaintenance faultsDirt in the intake airDir t that reaches the combustion chamber settles in the ring grooves where it causes abrasive wear in the ring grooves and at the piston ring flanks. This results in excessive ring height clearance and consequently to...
-
-
Technical Bulletin
- Brake cleaner - Note on storage
-
Jan 17
- Hella Ireland (1757)
-
...rake cleaner binds brake dust and reliably removes oil, grease and dirt without leaving any residue. As such, this tried and tested cleaning agent is used almost universally for all types of work in garages. The following conditions for correct storage of it must always be observed....
-
-
Technical Bulletin
- Mazda 3/6 series - Engine not running smoothly; Engine stalls sporadically
-
Jan 17
- Hella Ireland (1757)
-
...Mazda 3/6 series Engine code: PE, PY Year of construction: 10/2013 – 02/2014 Engine not running smoothly Engine stalls sporadically There have been complaints of unexpected engine stalling in the aforementioned vehicles. This may be due to a software error in the engine control unit...
